OpenROUTE GlobeTrotter 60
Routing with the OpenROUTE GlobeTrotter 60 for Dedicated Access Service
Configuration
Note: Connect up the console port prior to powering up the router. Otherwise, the router will not see that the console port is available for use.
To configure an OpenROUTE you must connect up a console to the Console port of the router. A null modem adapter is provided. Connect up the Null Modem to the Console cable provided and then to the serial port of a PC (or Mac with proper cables) with VT100 emulation software. 9600, 8, none 1.
If the router has not been preconfigured, it will run through an interactive script upon bootup.
Follow the script shown below.
Otherwise you can telnet into the box.
**********************************************************
Interface Configuration
**********************************************************
Type 'Yes' to Configure Interfaces
Type 'No' to skip Interface Configuration
Type 'Quit' to exit Quick Config
Configure Interfaces? (Yes, No, Quit): [Yes] <enter>
Type 'r' any time at this level to restart Interface Configuration
Intf 0 is Ethernet
Intf 1 is WAN PPP
Encapsulation for WAN 1 (PPP, Frame Relay): [PPP] Frame Relay
Internal clock speed (decimal) (4800 - 2048000): [56000] <enter>
This is all configured device information:
Intf 0 is Ethernet, Connector (10baseT, 10base2) auto-configured
Intf 1 is WAN 1 with Frame Relay Encapsulation, Connector auto-configured
Save this configuration? (Yes, No): [Yes] <enter>
Device configuration saved
**********************************************************
Protocol Configuration
**********************************************************
Type 'Yes' to Configure Protocols
Type 'No' to skip Protocol Configuration
Type 'Quit' to exit Quick Config
Configure Protocols? (Yes, No, Quit): [Yes] <enter>
Type 'r' any time at this level to restart Protocol Configuration
Configure IP? (Yes, No): [Yes]
Type 'r' any time at this level to restart IP Configuration
Configuring Per-Interface IP Information
Configuring Interface 0 (Ethernet)
Configure IP on this interface? (Yes, No): [Yes] <enter>
IP Address: [] LAN.LAN.LAN.1
Address Mask: [255.0.0.0] 255.255.255.0
Configuring Interface 1 (WAN Frame Relay)
Configure IP on this interface? (Yes, No): [Yes]
IP Address: [] SER.SER.SER.SER
Address Mask: [255.0.0.0] 255.255.255.0
Per-Interface IP Configuration complete
Configuring IP Routing Information
Enable Dynamic Routing? (Yes, No): [Yes] <enter>
Routing Configuration Complete
SNMP will be configured with the following parameters:
Community: public
Access: READ-ONLY
This is the information you have entered:
Interface # IP Address Address Mask
0 LAN.LAN.LAN.1 255.255.255.0
1 SER.SER.SER.SER 255.255.255.0
Save this configuration? (Yes, No): [Yes] <enter>
IP configuration saved
**********************************************************
Booting Configuration
**********************************************************
Type 'Yes' to Configure Booting
Type 'No' to skip Booting Configuration
Type 'Quit' to exit Quick Config
Configure Booting? (Yes, No, Quit): [Yes] <enter>
Type 'r' any time at this level to restart Booting Configuration
Previous Boot information
Booting Method: IBD Boot
IBD Load Name: gt60.ldc
Create an IBD boot record using this information? (Yes, No): [Yes] <enter>
Boot configuration saved
Enable Console Modem-Control? (Yes, No, Quit): [No] <enter>
Quick Config Done
Restart the router for this configuration to take effect
Restart the router? (Yes, No): [Yes] <enter>
RESTARTING THE ROUTER........
OpenROUTE (tm) Software
OpenROUTE is a registered trademark of OpenROUTE, Inc.
Copyright Notices:
Copyright 1985-1995 OpenROUTE, Inc.
Copyright 1984-1987, 1989 by J. Noel Chiappa
MOS Operator Control
*t 6
Gateway user configuration
config>network 1
Frame Relay user configuration
FR config>add proto ip SER.SER.SER.1 DLCI
FR config>exit
config>proto IP
Internet protocol user configuration
IP config>add route
IP destination [0.0.0.0]? <enter>
Address mask [0.0.0.0]? <enter>
Via gateway at [0.0.0.0]? SER.SER.SER.1
Cost [1]? <enter>
IP config>enable rip
IP config>enable send subnet-routes SER.SER.SER.SER
IP config>exit
config> <cntrl>-<p>
* re
Are you sure you want to restart the gateway? (Yes or [No]): yes
LAN.LAN.LAN.1 = Ethernet address of Customer Router
LAN.LAN.LAN = Customer Network Number
SER.SER.SER.SER = Serial address of Customer Router
SER.SER.SER.1 = Address of POP Router
DLCI = Customer DLCI
|
