Technical Library
|
|
Technical Library |
|
|
|
|
19 Oct 2000 
Certified Hardware & Software
What You Need
|
 |
Ascend Pipeline 50Routing with Ascend Pipeline 50 for LAN-ISDN Service ConfigurationIn the main edit window you will see the configure menu. Configuration of the parameters is described below. Main Edit Menu -+ | +- Configure +-------- LIACCT EDIT ---------+ +--------------------+ +--------------------+ |Configure... | |10-100 1 | |00-200 00:00:05 | |>Switch Type=*CUST.SWITCH* | | Link X | |>M31 Line Ch | | Chan Usage=Switch/Switch | | B1 . | | Ethernet Up | | My Num A=*CUST.PHONE.A* | | B2 . | | | | My Num B=*CUST.PHONE.B* | +--------------------+ +--------------------+ | SPID 1=*CUST.SPID.A* | |20-100 Sessions | |20-500 DYN Stat | | SPID 2=*CUST.SPID.B* | |> 0 Active | | Qual N/A 00:00:00 | | My Name=*ACCT.ID* | | | | 0K 0 channels | | My Addr=*LAN.LAN.LAN.LAN*/24 | | | | CLU 0% ALU 0% | | Rem Name= Net | +--------------------+ +--------------------+ | Rem Addr= 38.1.1.1/8 | |20-300 WAN Stat | |20-400 Ether Stat | | Dial #=*POP.PHONE.NUM* | |>Rx Pkt: 0^| |>Rx Pkt: 0 | | Route=IP | | Tx Pkt: 0 | | Tx Pkt: 1 | | Bridge=No | | CRC: 0v| | Col: 0 | | Send Auth=PAP | +--------------------+ +--------------------+ | Send PW=*PASSWORD* | |00-100 Sys Option | |00-300 HW Config | | Recv Auth=None | |>Security Prof: 3 ^| |>BRI U Interface ^| | Recv PW=N/A | | Software +4.5A+ | | Adrs: 00c07b520036 | | Save= | | S/N: 5366006 v| | Enet I/F: AUI v| Press Ctrl-n to move cursor to the next menu item. Press return to select it. Press Tab to move to another window --- thick border indicates active window. The telco should be able to tell you your Switch Type, Phone Numbers, and SPIDS.
*LAN.LAN.LAN.LAN* is the address of your router. After configuring the values in the configure menu, then press Esc to get to the main edit menu. You will then need to go under the following menus to enter additional values and confirm that the values set in the Configure Menu are there. Highlight the Save= entry and press Return, this will save the cofiguration information. Go under the Ethernet menu, then under the Connections menu, then under the Net menu. In this menu you will see a lot of the information you entered in the Configure Menu. Please make sure that it is correct. ================================================================================ Main Edit Menu -+ | +- 20-000 Ethernet -+ | +- 20-100 Connections -+ | +- 20-101 Net +-------- LIACCT EDIT ---------+ +--------------------+ +--------------------+ |20-101 Net | |10-100 1 | |00-200 00:00:05 | |>Station=Net | | Link X | |>M31 Line Ch | | Active=Yes | | B1 . | | Ethernet Up | | Encaps=MPP | | B2 . | | | | Dial #=*POP.PHONE.NUM* | +--------------------+ +--------------------+ | Route IP=Yes | |20-100 Sessions | |20-500 DYN Stat | | Route IPX=No | |> 0 Active | | Qual N/A 00:00:00 | | Bridge=N/A | | | | 0K 0 channels | | Dial Broadcast=N/A | | | | CLU 0% ALU 0% | | Encaps Options... | +--------------------+ +--------------------+ | IP Options... | |20-300 WAN Stat | |20-400 Ether Stat | | Ipx Options... | |>Rx Pkt: 0^| |>Rx Pkt: 0 | | Session Options... | | Tx Pkt: 0 | | Tx Pkt: 1 | | Telco Options... | | CRC: 0v| | Col: 0 | | | +--------------------+ +--------------------+ | | |00-100 Sys Option | |00-300 HW Config | | | |>Security Prof: 3 ^| |>BRI U Interface ^| | | | Software +4.5A+ | | Adrs: 00c07b520036 | | | | S/N: 5366006 v| | Enet I/F: AUI v| Press Ctrl-n to move cursor to the next menu item. Press return to select it. Press Tab to move to another window --- thick border indicates active window. Go to the Encaps Options... menu: ================================================================================ Main Edit Menu -+ | +- 20-000 Ethernet -+ | +- 20-100 Connections -+ | +- 20-101 Net Encaps Options... +-------- LIACCT EDIT ---------+ +--------------------+ +--------------------+ |20-101 Net | |10-100 1 | |00-200 00:00:05 | | Encaps Options... | | Link X | |>M31 Line Ch | | >Send Auth=PAP ^| | B1 . | | Ethernet Up | | Send PW=*PASSWORD* | | B2 . | | | | Recv PW=N/A | +--------------------+ +--------------------+ | Base Ch Count=1 | |20-100 Sessions | |20-500 DYN Stat | | Min Ch Count=1 | |> 0 Active | | Qual N/A 00:00:00 | | Max Ch Count=2 | | | | 0K 0 channels | | MRU=1524 | | | | CLU 0% ALU 0% | | LQM=No | +--------------------+ +--------------------+ | LQM Min=600 | |20-300 WAN Stat | |20-400 Ether Stat | | LQM Max=600 | |>Rx Pkt: 0^| |>Rx Pkt: 0 | | Link Comp=None | | Tx Pkt: 0 | | Tx Pkt: 1 | | VJ Comp=Yes | | CRC: 0v| | Col: 0 | | Dyn Alg=Linear | +--------------------+ +--------------------+ | Sec History=15 | |00-100 Sys Option | |00-300 HW Config | | Add Pers=5 | |>Security Prof: 3 ^| |>BRI U Interface ^| | | | Software +4.5A+ | | Adrs: 00c07b520036 | | v| | S/N: 5366006 v| | Enet I/F: AUI v| Press Ctrl-n to move cursor to the next menu item. Press return to select it. Press Tab to move to another window --- thick border indicates active window. Verify that all of the settings are correct, You may want to change the MPP options. See MPP Configuration. Press Esc and this will bring you back to the Connections Menu. Go into the Session Options menu: ================================================================================ Main Edit Menu -+ | +- 20-000 Ethernet -+ | +- 20-100 Connections -+ | +- 20-101 Net Session Options... +-------- LIACCT EDIT ---------+ +--------------------+ +--------------------+ |20-101 Net | |10-100 1 | |00-200 00:00:05 | | Session Options... | | Link X | |>M31 Line Ch | | >Data Filter=0 ^| | B1 . | | Ethernet Up | | Call Filter=0 | | B2 . | | | | Idle=600 | +--------------------+ +--------------------+ | Preempt=60 | |20-100 Sessions | |20-500 DYN Stat | | Backup=N/A | |> 0 Active | | Qual N/A 00:00:00 | | | | | | 0K 0 channels | | | | | | CLU 0% ALU 0% | | | +--------------------+ +--------------------+ | | |20-300 WAN Stat | |20-400 Ether Stat | | | |>Rx Pkt: 0^| |>Rx Pkt: 0 | | | | Tx Pkt: 0 | | Tx Pkt: 1 | | | | CRC: 0v| | Col: 0 | | | +--------------------+ +--------------------+ | | |00-100 Sys Option | |00-300 HW Config | | | |>Security Prof: 3 ^| |>BRI U Interface ^| | | | Software +4.5A+ | | Adrs: 00c07b520036 | | | | S/N: 5366006 v| | Enet I/F: AUI v| Press Ctrl-n to move cursor to the next menu item. Press return to select it. Press Tab to move to another window --- thick border indicates active window. Verify the above information. Note: Idle= is the number of seconds that the Link will stay up when no IP traffic is being passed. Press Esc to get back to the Sessions... menu. Go to the Telco Options... menu: ================================================================================ Main Edit Menu -+ | +- 20-000 Ethernet -+ | +- 20-100 Connections -+ | +- 20-101 Net Telco Options... +-------- LIACCT EDIT ---------+ +--------------------+ +--------------------+ |20-101 Net | |10-100 1 | |00-200 00:00:05 | | Telco Options... | | Link X | |>M31 Line Ch | | >AnsOrig=Call Only ^| | B1 . | | Ethernet Up | | Callback=No | | B2 . | | | | Call Type=Switched | +--------------------+ +--------------------+ | Group=N/A | |20-100 Sessions | |20-500 DYN Stat | | Data Svc=*LINE.SPEED* | |> 0 Active | | Qual N/A 00:00:00 | | Force 56=No | | | | 0K 0 channels | | Bill #= | | | | CLU 0% ALU 0% | | | +--------------------+ +--------------------+ | | |20-300 WAN Stat | |20-400 Ether Stat | | | |>Rx Pkt: 0^| |>Rx Pkt: 0 | | | | Tx Pkt: 0 | | Tx Pkt: 1 | | | | CRC: 0v| | Col: 0 | | | +--------------------+ +--------------------+ | | |00-100 Sys Option | |00-300 HW Config | | | |>Security Prof: 3 ^| |>BRI U Interface ^| | | | Software +4.5A+ | | Adrs: 00c07b520036 | | | | S/N: 5366006 v| | Enet I/F: AUI v| Press Ctrl-n to move cursor to the next menu item. Press return to select it. Press Tab to move to another window --- thick border indicates active window. Verify the information in the Telco Options menu... Your telco should have provided you with the proper Data Scv (or line speed). This will either be 56K or 64K. Press Esc to get back to the Sessions menu, then press Esc again to get to the Ethernet... menu. Go to the Mod Config... menu: ================================================================================ Main Edit Menu -+ | +- 20-000 Ethernet -+ | +- 20-800 Mod Config +-------- LIACCT EDIT ---------+ +--------------------+ +--------------------+ |20-800 Mod Config | |10-100 1 | |00-200 00:00:05 | |>Ether Options... | | Link X | |>M31 Line Ch | | SNMP Options... | | B1 . | | Ethernet Up | | Bridging=No | | B2 . | | | | Shared Prof=No | +--------------------+ +--------------------+ | Telnet PW= | |20-100 Sessions | |20-500 DYN Stat | | Domain Name=*DOMAIN* | |> 0 Active | | Qual N/A 00:00:00 | | Pri DNS=38.8.82.2 | | | | 0K 0 channels | | Sec DNS=38.8.84.2 | | | | CLU 0% ALU 0% | | Syslog=No | +--------------------+ +--------------------+ | Log Host=N/A | |20-300 WAN Stat | |20-400 Ether Stat | | Log Facility=N/A | |>Rx Pkt: 0^| |>Rx Pkt: 0 | | | | Tx Pkt: 0 | | Tx Pkt: 1 | | | | CRC: 0v| | Col: 0 | | | +--------------------+ +--------------------+ | | |00-100 Sys Option | |00-300 HW Config | | | |>Security Prof: 3 ^| |>BRI U Interface ^| | | | Software +4.5A+ | | Adrs: 00c07b520036 | | | | S/N: 5366006 v| | Enet I/F: AUI v| Press Ctrl-n to move cursor to the next menu item. Press return to select it. Press Tab to move to another window --- thick border indicates active window. Verify the setting in the Mod Config... menu. *DOMAIN* is your InterNIC registered domain name.
Pri DNS should have your Primary assigned DNS Name Resolver. Go to the Ether Options... menu: ================================================================================ Main Edit Menu -+ | +- 20-000 Ethernet -+ | +- 20-800 Mod Config Ether Options... +-------- LIACCT EDIT ---------+ +--------------------+ +--------------------+ |20-800 Mod Config | |10-100 1 | |00-200 00:00:05 | | Ether Options... | | Link X | |>M31 Line Ch | | >IP Adrs=*LAN.LAN.LAN.LAN*/24| | B1 . | | Ethernet Up | | 2nd Adrs=0.0.0.0 | | B2 . | | | | RIP=Off | +--------------------+ +--------------------+ | Proxy Mode=Always | |20-100 Sessions | |20-500 DYN Stat | | Filter=0 | |> 0 Active | | Qual N/A 00:00:00 | | IPX Fram=802.3 | | | | 0K 0 channels | | | | | | CLU 0% ALU 0% | | | +--------------------+ +--------------------+ | | |20-300 WAN Stat | |20-400 Ether Stat | | | |>Rx Pkt: 0^| |>Rx Pkt: 0 | | | | Tx Pkt: 0 | | Tx Pkt: 1 | | | | CRC: 0v| | Col: 0 | | | +--------------------+ +--------------------+ | | |00-100 Sys Option | |00-300 HW Config | | | |>Security Prof: 3 ^| |>BRI U Interface ^| | | | Software +4.5A+ | | Adrs: 00c07b520036 | | | | S/N: 5366006 v| | Enet I/F: AUI v| Press Ctrl-n to move cursor to the next menu item. Press return to select it. Press Tab to move to another window --- thick border indicates active window. Verify the above information: Press Esc and go to the Static Rtes menu: ================================================================================ Main Edit Menu -+ | +- 20-000 Ethernet -+ | +- 20-300 Static Rtes +-------- LIACCT EDIT ---------+ +--------------------+ +--------------------+ |20-300 Static Rtes | |10-100 1 | |00-200 00:00:05 | |>20-3**Default | | Link X | |>M31 Line Ch | | 20-301 | | B1 . | | Ethernet Up | | 20-302 | | B2 . | | | | 20-303 | +--------------------+ +--------------------+ | | |20-100 Sessions | |20-500 DYN Stat | | | |> 0 Active | | Qual N/A 00:00:00 | | | | | | 0K 0 channels | | | | | | CLU 0% ALU 0% | | | +--------------------+ +--------------------+ | | |20-300 WAN Stat | |20-400 Ether Stat | | | |>Rx Pkt: 0^| |>Rx Pkt: 0 | | | | Tx Pkt: 0 | | Tx Pkt: 1 | | | | CRC: 0v| | Col: 0 | | | +--------------------+ +--------------------+ | | |00-100 Sys Option | |00-300 HW Config | | | |>Security Prof: 3 ^| |>BRI U Interface ^| | | | Software +4.5A+ | | Adrs: 00c07b520036 | | | | S/N: 5366006 v| | Enet I/F: AUI v| Press Ctrl-n to move cursor to the next menu item. Press return to select it. Press Tab to move to another window --- thick border indicates active window.Go to the 20-3**Default menu: ================================================================================ Main Edit Menu -+ | +- 20-000 Ethernet -+ | +- 20-300 Static Rtes 20-3**Default +-------- LIACCT EDIT ---------+ +--------------------+ +--------------------+ |20-3**Default | |10-100 1 | |00-200 00:00:05 | |>Name=Default | | Link X | |>M31 Line Ch | | Active=Yes | | B1 . | | Ethernet Up | | Dest=0.0.0.0/0 | | B2 . | | | | Gateway=38.1.1.1 | +--------------------+ +--------------------+ | Metric=1 | |20-100 Sessions | |20-500 DYN Stat | | Private=Yes | |> 0 Active | | Qual N/A 00:00:00 | | | | | | 0K 0 channels | | | | | | CLU 0% ALU 0% | | | +--------------------+ +--------------------+ | | |20-300 WAN Stat | |20-400 Ether Stat | | | |>Rx Pkt: 0^| |>Rx Pkt: 0 | | | | Tx Pkt: 0 | | Tx Pkt: 1 | | | | CRC: 0v| | Col: 0 | | | +--------------------+ +--------------------+ | | |00-100 Sys Option | |00-300 HW Config | | | |>Security Prof: 3 ^| |>BRI U Interface ^| | | | Software +4.5A+ | | Adrs: 00c07b520036 | | | | S/N: 5366006 v| | Enet I/F: AUI v| Press Ctrl-n to move cursor to the next menu item. Press return to select it. Press Tab to move to another window --- thick border indicates active window. Verify the above information. Press Esc until you reach the Main menu... You will be prompted if you save configurtation changes. Answer Yes. To test the connectivity:
     |